联系我们
名称：滴灌带诚信厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
滴灌带安装
滴灌带安装
Installation of drip irrigation belt
1、 按设计文件要求，全面核对设备型号、规格、数量和质量，严禁使用不合格产品。待安装设备应保持清洁，塑料管不得抛摔、拖拉和曝晒。
1. According to the requirements of design documents, comprehensively check the model, specification, quantity and quality of equipment, and prohibit the use of unqualified products. The equipment to be installed shall be kept clean, and the plastic pipe shall not be thrown, dragged or exposed to the sun.
2、 按设计要求和流向标记安装水表、阀门、过滤器。过滤器和支管之间通过带螺纹的直通连接。
2. Install water meter, valve and filter according to design requirements and flow direction mark. The filter and the branch pipe are connected through a threaded straight connection.
3、 螺纹管件安装
3. Installation of threaded pipe fittings
滴灌系统安装注意事项滴灌系统安装注意事项
Precautions for installation of drip irrigation system
时需缠生胶带，直通锁母应拧紧。
Raw tape shall be wrapped and straight lock nut shall be tightened.
4、 旁通安装前首先在支管上用专用打孔器打孔。打孔时，打孔器不能倾斜，钻头入管深度不得超过1/2管径;然后将旁通压入支管。
4. Before the bypass installation, first use a special hole punch on the branch pipe. When drilling, the perforator shall not be inclined, and the depth of the drill into the pipe shall not exceed 1 / 2 of the pipe diameter; then, the bypass shall be pressed into the branch pipe.
5、 按略大于植物行的长度裁剪滴灌管(带)，滴灌管(带)沿植物行布置，然后一端与旁通相连接。
5. Cut the drip irrigation pipe (belt) according to the length slightly larger than the row of plants, arrange the drip irrigation pipe (belt) along the row of plants, and then connect one end with the bypass.
Installation of drip irrigation belt
1、 按设计文件要求，全面核对设备型号、规格、数量和质量，严禁使用不合格产品。待安装设备应保持清洁，塑料管不得抛摔、拖拉和曝晒。
1. According to the requirements of design documents, comprehensively check the model, specification, quantity and quality of equipment, and prohibit the use of unqualified products. The equipment to be installed shall be kept clean, and the plastic pipe shall not be thrown, dragged or exposed to the sun.
2、 按设计要求和流向标记安装水表、阀门、过滤器。过滤器和支管之间通过带螺纹的直通连接。
2. Install water meter, valve and filter according to design requirements and flow direction mark. The filter and the branch pipe are connected through a threaded straight connection.
3、 螺纹管件安装
3. Installation of threaded pipe fittings
滴灌系统安装注意事项滴灌系统安装注意事项
Precautions for installation of drip irrigation system
时需缠生胶带，直通锁母应拧紧。
Raw tape shall be wrapped and straight lock nut shall be tightened.
4、 旁通安装前首先在支管上用专用打孔器打孔。打孔时，打孔器不能倾斜，钻头入管深度不得超过1/2管径;然后将旁通压入支管。
4. Before the bypass installation, first use a special hole punch on the branch pipe. When drilling, the perforator shall not be inclined, and the depth of the drill into the pipe shall not exceed 1 / 2 of the pipe diameter; then, the bypass shall be pressed into the branch pipe.
5、 按略大于植物行的长度裁剪滴灌管(带)，滴灌管(带)沿植物行布置，然后一端与旁通相连接。
5. Cut the drip irrigation pipe (belt) according to the length slightly larger than the row of plants, arrange the drip irrigation pipe (belt) along the row of plants, and then connect one end with the bypass.
